Asphalt Mix Designs Oklahoma

PDF AASHTO Pavement Thickness Design Guide

basis for the pavement design. 2. Design variables a. Analysis period (n) - n is the period of time for which the analysis is to be conducted. Normally 50 years for concrete and 30 years for asphalt. b. Design Traffic (ESALs) - ESALs is the estimate of number of Equivalent 18 kip Single Axle

Learn More

PDF HMA PRODUCTION MANUAL - Michigan

HOT MIX ASPHALT (HMA) MIX DESIGN LABORATORY QUALIFICATIONS To be qualified to submit HMA mix designs for projects with the Michigan Department of Transportation (MDOT) oversight, the laboratory must supply documentation for meeting the following criteria: 1. The HMA Mix Designer preparing the HMA mix design must have successfully completed the MDOT

Learn More

How to Install Asphalt Milling for a Driveway | Hunker

Asphalt millings are recycled in almost every new asphalt mix that is produced. Not all of the milled asphalt is reused in new asphalt. Most projects limit millings to no more than 30 percent of the volume of the new mix. There are other uses for millings such as on driveways or on less traveled roads.

Learn More

Concrete Mix Design | Stonemont Solutions

Concrete Mix Design and Quality Control Software Management System StonemontQC includes a powerful concrete mix design and quality control software program for concrete producers. StonemontQC is fully integrated with the aggregate portion allowing for mix component properties to be easily kept current with data from aggregate plants.

Learn More

Asphalt Driveways - All About Asphalt Driveways

The black asphalt heats up from the warmth of the sun and melts off the snow and ice much faster. Unfortunately, asphalt driveways come in only one color. However, new sealers on the market which offer a variety of colors to choose from. See some different Colorful Design Ideas For Asphalt Driveways.

Learn More

Develop Mix Design and Analysis Procedures for Asphalt

Develop Mix Design and Analysis Procedures for Asphalt Mixtures Containing High-RAP Contents – TPF 5(294) FHWA Asphalt Binder Expert Task Group Oklahoma City, Oklahoma September 17, Louay N. Mohammad, Ph.D. Department of Civil and Environmental Engineering Louisiana Transportation Research Center

Learn More

PDF Standard Construction Specifications for Asphalt Surfacing

Mix Design Methods for Asphalt Concrete, by The Asphalt Institute. Page 3 Standard Construction Specifications Division 40 - Asphalt Surfacing Revised 11/08 The number of blows of the Compaction hammer used in the Marshall Mix Design will be fifty (50) blows per side of specimen.

Learn More

Denver Approved Asphalt Mix Designs for Paving, list

Denver Approved Asphalt Mix Designs for Paving, list expires July1, 2015. Mix design optimum values shown for Target %AC, %VTM, % VMA with tolerances to derive the Job Mix or Allowable Mix Production Range ( AMPR ) limits. RAP mix and polymer binder OK as less than 30% binder replacement PG 76-28 05/09/14 Suncor 5.1% 3.8% 14.9% 2.673

Learn More

Demonstration 3: Permeable Paving Materials and

The parking aisles, consisting of 16,600 square feet, were paved with porous asphalt, a special mix that allows water to pass through the pavement surface. Underneath the porous pavers and asphalt is an infiltration bed of crushed stone that filters contaminants and allows water to slowly percolate into the underlying soil.

Learn More

13 Pavement Defects and Failures You Should Know!

This can be because the mix was mixed and placed too dry; Fine aggregate mix with low penetration asphalt & absorptive aggregates; poor choice of asphalt binder in the mix design; or aging dried out asphalt. FIX: Less severe cracks measuring 1/2 inch or less can be sealed to prevent moisture from entering into the sub grade.

Learn More

Materials & Pavements Division | UDOT

Asphalt Engineer Email:[email protected] 801-633-8770 (Cell) Dave Thomas Lead Binder Technician Email:[email protected] 801-633-6241 (Cell) Mike Evans Asphalt Lab Technician Email:[email protected] 801-633-6264 (Cell) Trevor Vlam Asphalt Lab Technician Email:[email protected] 801-815-9644 (Cell) Clark Allen Lead Asphalt Mix Lab Technician

Learn More

Aggregate Blending for Asphalt Mix Design

ASPHALT #MIX #DESIGN #AGGREGATE #BLENDING From the beginning of asphalt mixture design, it was desired to understand the interaction of aggregates, asphalt,

Learn More

Asphalt Mix Designs - Free PDF eBook

All Asphalt Mix Designs Approved for Use (Listed) on Contracts in 1 day ago All Asphalt Mix Designs Approved for Use (Listed) on Contracts in WS3c00931300700 Asphalt Concrete, Type S3 (PG 64-22 OK). jCOUNTY_GRP2_PDF.pdf

Learn More

PDF Oklahoma Department of Transportation Special Provision

Asphalt Cement d, % of mix mass $ 3.9 $ 4.3 $ 4.8 $ 5.3 $ 5.8 Performance grade asphalt cement eeeee a Table 708:6 reflects the sieve size boundaries for design and JMF purposes. After the design is established, the JMF will designate combined aggregate sieve requirements with tolerances in Table 708:12.

Learn More

Basic Asphalt Materials Mixture Design and Testing

Mix Design Fundamentals HMA consists of two basic ingredients: aggregate and asphalt binder. HMA mix design is the process of determining what aggregate to use, what asphalt binder to use and what the optimum combination of these two ingredients ought to be. There are several different methods used to go

Learn More

PDF Design Guide for Concrete Parking Lots

Mix and Materials Concrete is commonly specified by compressive strength f'(c ). It is typical to specify a minimum design strength of 4000 psi at 28 days with a maximum water-cementitious ratio (w/c) of 0.45, in most areas of the country. Since South Dakota experiences freeze-thaw cycles, it is recommended to further specify a mix containing

Learn More

Development of Hot Mix Asphalt Pavement Performance

this material. Two designs were included in the development process. The planned structural pavement design included the following two hot mix asphalt mixes: An HMA surface course containing a polymer-modified asphalt (PG 64-28PM) and a representative aggregate from

Learn More

Submittal and Approval of Hot Mix Asphalt Mix Designs (SOP

Hot Mix Asphalt Mix Designs (SOP 3-4) Purpose: The purpose of this document is to establish an acceptance procedure for hot mix asphalt mix designs. Discussion: Asphalt mix designs submitted to the TDOT must exhibit certain physical performance properties indicated in Standard Specifications including but

Learn More

City of Oakland | Public Works

City of Oakland Announces Appointment of New Public Works Director - G. Harold Duffey Brings Skills and Expertise to Lead the Department. Oakland City Administrator Ed Reiskin announced today the appointment of G. Harold Duffey as the new Oakland Public Works Director effective July 26, 2021. May 13, 2021.

Learn More

Approved Asphalt Mix Designs for Major Arterial or

APPROVED ASPHALT MIX DESIGNS FOR MAJOR ARTERIAL OR ARTERIAL STREETS . CITY OF BUCKEYE. Engineering Department. N:\Construction\Approved Asphalt Designs\ ASPHALT Designs\ Approved ASPHALT Mix Designs - Rev 01-28-2020. MAR = MARSHALL GYR = GYRATORY. Supplier Name. Hot-Plant # Hot-Plant Location. Product Code Road Type. Mix Size Mix

Learn More

PDF Performance Specifications - Pavement - Oklahoma

1. The Oklahoma Department of Transportation Standard Specifications 2. All adopted Codes of the Oklahoma State Fire Marshall Due to market volatility in asphalt material, contracted parties may request a price adjustment when the Oklahoma Department of Transportation Monthly Asphalt Binder Price Index fluctuates by three percent (3%) or more.

Learn More

Best 30 Asphalt Contractor in Oklahoma City, OK with

Asphalt Contractor in Oklahoma City on YP.com. See reviews, photos, directions, phone numbers and more for the best Asphalt Paving & Sealcoating in Oklahoma City, OK.

Learn More

National Center for Asphalt Technology

Four test sections on the Test Track focus on the balanced mix design of asphalt mixtures. These sections are sponsored by the Oklahoma and Texas Departments of Transportation. Oklahoma's balanced mix design approach requires the use of the Hamburg wheel tracking test to evaluate rutting resistance and the Illinois flexibility index to

Learn More

PDF Approved Asphalt Mix Designs

Approved Asphalt Mix Designs.xlsx Author: tsandy Created Date: 4/15/ 12:30:09 PM

Learn More

Venturi-Mixer Series 225 to 600 tph - CMI Roadbuilding

Available as portable drums in capacities of 225 to 500tph and in stationary drums up to 600tph. The Venturi-Mixer features a unique design that allows recycled material to be used without blue smoke generation, reduces dust loadings in the exhaust gas while keeping final mix and exit gas temperatures in close relation to each other.

Learn More

PDF NCAT+MnROAD: Long Term Pavement Preservation Benefit

Innovative porous surface mix design • Asphalt based high friction alternatives • Lower cost thinlay rutting and cracking • Mix improvements on longitudinal joint. Thickness Design Optimization • Soft subgrade imported to Track for Oklahoma - 10" failed (salvaged with high polymer inlay) - 14" found to be perpetual

Learn More

SUBJECT: HOT MIX ASPHALT (HMA) MIXTURE DESIGN AND

development and review of hot mix asphalt (HMA) mixture designs. This MM outlines a complete procedure for the uniform design of volumetric mixtures for 6.3 Top Course HMA, 9.5 Top Course HMA, 12.5 Top Course HMA, 19.0 Binder Course HMA, 25.0 Binder Course HMA, or 37.5 Base Course HMA.

Learn More

Asphalt vs. Concrete Driveway | 6 Factors to Consider

Like concrete, asphalt is an aggregate material of a mixture of stone and sand, but it contains tar-like petroleum instead of cement as the adhesive base. Contractors use high temperatures to liquefy hot mix asphalt and create the driveway before it cools and becomes a solid.

Learn More

Mix Design Technology Certification - Asphalt Institute

The Mix Design Technology Certification (MDT) course provides advanced technicians, designers, and engineers responsible for mix designs with a thorough understanding of the properties of the materials which compose asphalt mixtures, as well as the physical and mathematical processes involved in producing a successful asphalt mixture design.

Learn More

Colored Pavement Material Guidance | National Association

Colored asphalt is composed of the same material as standard asphalt, but has a colored pigment added. The colored asphalt may be installed as a thin layer over conventional asphalt to reduce cost. One well-known use of colored asphalt is Bend, Oregon's red bike lanes, which utilize a localized red pigment in the colored asphalt.

Learn More

Mix Design – Pavement Interactive

Mix Design. The two key components of pavement design are mix design and structural design. This section deals with HMA and PCC mix design. The goal of mix design is to determine the optimum mixture of component materials for a given application. This includes detailed evaluations of aggregate, asphalt

Learn More

Inquiry